Sensors and Probes

The ATI-5005B Water Sensor is designed to detect water at a point location in tanks, sumps, piping and any other location to detect the presence of water or conductive liquids.

September 10, 2008

The new ATI-5005TN is an economical, Nylon housing version of our basic ATI-5005B and stainless-steel ATI-5005TS sensors.  When ordered with Teflon cable, like the ATI-5005TS, it is safe for use in areas with high sanitary requirements such as clean rooms, food, dairy and medical.

The new ATI-5005TS Water Sensor is a heavy-duty, stainless-steel version of our ATI-5005B sensor.  It has been designed for more extreme environmental conditions, able to withstand corrosion, higher temperature and pressure. When ordered with Teflon cable, it is safe for use in areas with high sanitary requirements such as clean rooms, food, dairy and medical.

NOTE:  The information provided is only preliminary.  Specifications will be updated once this sensor has been tested to determine its limits.

The ATI-5005F Floor Water Sensor is designed to detect water or other conductive liquids at point locations.  It can be placed directly on the floor or fastened to the wall near the floor.  The slotted mounting tabs provide easy installation and adjustment of this versatile sensor.

When placed on the floor, the sensing electrodes are positioned approximately 1/8" (3.2mm) above the floor.  This sensor can be manufactured so that the electrodes are closer to the floor if required (Contact us for details).

 

The first of its kind, the ATI-5005N narrow-space water sensor was specifically designed to monitor the water level in deep underground well pipes, but can also be used for other similar applications.  Manufactured with stainless-steel, it is highly resistant to corrosion, and is narrow enough to fit in pipes as small as 1/2 inch (13 mm) inside diameter.

This sensor can be manufactured in lengths from 6 inches (15.2 cm) up to 36 inches (91.5 cm) with 1, 2 or 3 detection levels.

The ATI-5007B is a flexible cable sensor that is primarily used for detecting water and petroleum leaks in the interstitial space of double-walled underground storage tanks.  The petroleum-sensing portion of the cable can detect petroleum products along the full length of the cable.  The water-sensing wires can be adjusted to detect water at any specific point along the cable.  Unlike many other petroleum-sensing cables, our cable can be reused even after it has been exposed to petroleum-based products.

The ATI-5008 is a vacuum type sensor specifically designed to quickly detect a loss of vacuum in the interstitial space of double-walled petroleum storage tanks.

The ATI-5010 is a float switch type sensor designed to detect rising or lowering levels of liquid inside storage tanks, pits or sumps.  A change in fluid level moves the float which activates or deactivates an alarm/indicator.  This sensor is available in many sizes as either the single-level version with integral mounting ears (ATI-5010B), or the 1-to-3-level tank-mount version (ATI-5010T).

Our ATI-5010B Liquid Level Sensor (as shown at left) has been re-designed using a Nylon housing with integral mounting ears, making the entire assembly corrosion resistant.  It installs easily and quickly using two (2) #8 flathead screws.

Download the User Configuration Sheet to select the correct sensor for your application.

The ATI-5010W Interstitial Leak Sensor is a non-discriminating liquid leak sensor which will detect the rising or lowering of liquids at a single location.  This sensor is suited for various applications such as: Interstitial space of steel tanks, sumps, dispensers, wells, containers, vats, manholes, trenches, etc.

The ATI-5010S Sump Brine Sensor is primarily used to detect rising or falling levels of brine in the interstitial space of double-wall tanks.  A leak in the tank causes a change in the brine level which moves the internal floats of the sensor and triggers an alarm.

The ATI-5016A is a flexible cable sensor for detecting the presence of petroleum leaks around tanks, along pipes, in containment pans and trenches, and any other areas where a petroleum leak may happen.  Unlike many other petroleum-sensing cables, our cable can be reused even after it has been exposed to petroleum-based products.

The ATI-5020 Liquid Level Probe provides up to 4 level detection points for most liquids.  The probe feature a stainless-steel tube assembly which is certified explosion-proof and rated for Class I, Groups C & D locations.

The ATI-5020 provides all the necessary features to monitor and operate a day tank that is connected to a supply tank in a Genset application.  It provides the necessary 4 incremental level detection points to indicate the overfill, pump-off, pump-on and empty fuel levels in the day tank.

Download the appropriate User Configuration Sheet to provide data for manufacturing the probe for your application.

The ATI-5025A Water Sensing Cable detects the presence of water or other conductive liquids at any point along the cable.  This sensor is available in almost any length and is ideal for detecting the presence of water in basements, warehouses, museums, data rooms, ceilings, underground parking lots and tunnels.

The ATI-5029 Liquid Level Measurement Probe provides continuous liquid level monitoring in increments of one inch or 2 cm, allowing accurate depth measurement readings.  This sensor is designed to be used with the ATI-DM335 display module.  The probe feature a stainless-steel tube assembly which is certified explosion-proof and rated for Class I, Groups C & D locations.

The ATI-5020 provides continuous fuel level monitoring in the supply tank in a Genset application.

Download the User Configuration Sheet to provide data for manufacturing the probe for your application.